WJ Series High Voltage AC/DC Power Supplies

AMS item number: SW11410

Input Voltage 102-264 VAC; Max. Output Voltage 70-125 kVDC; Max. Power 600 W; Efficiency >85%;... more

Product information "WJ Series High Voltage AC/DC Power Supplies"

Input Voltage 102-264 VAC; Max. Output Voltage 70-125 kVDC; Max. Power 600 W; Efficiency >85%; Voltage Regulation <0.005%; Current Regulation <0.1%

XP Glassman’s WJ Series of 600 W high voltage AC/DC power supplies feature flexible embedded controls with low ripple and noise. They are air insulated, fast response, 3U rack-mount units with tight regulation and extremely low arc discharge currents. A range of models is available with output voltage ranges from 0 to 70 kVDC through 0 to 125 kVDC.

The WJ series features “air” as the primary dielectric medium. No oil or encapsulation is used which would impede serviceability or increase weight. Internal circuitry constantly senses and integrates arcs that occur over a given time. In the event a system or load arcing problem develops and exceeds factory-set parameters, the power supply will cycle off in an attempt to clear the fault and then automatically restart after a preset “off dwell time”. The WJ Series’ high voltage output is inhibited for a short period after each load arc to help extinguish the arc.

Typically, ripple is less than 0.1% RMS of rated voltage at full load. Off-the-line pulse-width modulation (PWM) provides high efficiency and a reduced parts count for improved reliability. Front-panel digital encoders provide high-resolution local adjustment of voltage and current program. Integral RS-232, USB and optional Ethernet communications provide remote control program and monitor.

The WJ Series’ standard operation mode is constant voltage/current. Automatic crossover from constant-voltage to constant-current regulation provides protection against overloads, arcs and short circuits. A rear panel switch allows selection of either constant-current or current-trip operation. Thermostats and fan RPM sensing shut down the power supply due to over-temperature or reduced fan speeds.

Standard accessories for the WJ Series include a detachable 2,4 m shielded high voltage coaxial output cable, line cord, null modem cable and USB cable.

The WJ Series supplies with 230 VAC input option (198 to 264 VAC RMS, 48 to 63 Hz) are fully compliant with the following European directives:

EN61000-3-2, Line Harmonics
EN61010/ IEC61010, Safety
EN61000-6-4, Conducted and Radiated Emissions
EN61000-6-2:2005, Conducted and Radiated Immunity
2011/65/EU, Restriction of the Use of Hazardous Substances (RoHS)

Key Features:

3U Rack Mount
Air Insulated
Maximum Output Power: 600 W
Maximum Output Voltage: 70 to 125 kVDC
Maximum Output Current: 5 to 8.6 mA
Low Ripple: <0.1% of Rated Voltage at Full Load
Tight Regulation
Static Voltage Regulation: <0.005% for Specified Line and Load Variations
Current Regulation: <0.1% From Short Circuit to Rated Voltage at Any Load Condition
Constant Voltage/Constant Current Operation
Arc Quench & Arc Count
Front Panel, Remote, RS232, USB & Optional Ethernet Control
Input Voltage: 102 to 132, 198 to 264 VAC RMS, 48 to 63 Hz, Single Phase
Efficiency: >85% Typical at Full Load
Output Voltage Accuracy: 0.5% of Setting + 0.2% of Rated
Output Voltage Repeatability: <0.1% of Rated Voltage
Maximum Stored Energy: 8.0 to 15.0 J
Voltage Monitor: 0 to +10 VDC Signal for 0 to Rated Voltage
Current Monitor: 0 to +10 VDC Signal for 0 to Rated Current
Stability: 0.01%/h After 0.5 h Warm-up, 0.05% per 8 h
Polarity: Positive or Negative Polarity With Respect to Chassis Ground
Protection: Against All Overload Conditions, Including Arcs and Short Circuits
Signals Provided on the Remote Interface Connector: Safety Interlock, Voltage & Current Program/Monitor, HV Enable, HV Status, Fault Status, +10 V Reference, I/V Mode Status
Options: 100, 230 VAC Input, Blank Front Panel, Zero Start Interlock, 0 to 5 V Voltage & Current Program/Monitor, Arc Count and/or Quench, Virtual RS-232 COM Port Over Ethernet Network
3 Year Warranty
Approvals: IEC61010-1:2010; EN61000-6-4:2007, Class A EN61000-6-2:2005
Operating Temperature: -20 to +40 °C
Dimensions: 132.5 x 482.6 x 520.7 mm

Applications: High Voltage, High Power Applications; Photonics; Healthcare (Analytical, Diagnostics, Detectors); Industrial; Semiconductor Manufacturing; Research; Other